1
Scope
2 References
3 Abbreviations
4 Definitions
5 Architecture of the optical access
network
5.1 Network architecture
5.1.1 FTTCab/C/B scenario
5.1.2 FTTH scenario
5.2 Reference configuration
5.2.1 Service Node Interface
5.2.2 Interface at the reference points S/R and R/S
5.3 Functional
blocks
5.4 ONU functional block
5.4.1 Optical Distribution Network
interface
5.4.2 Multiplexing
5.4.3 User Port
5.4.4 ONU powering
5.5 Optical Line Termination
functional block
5.6 Optical Distribution Network
functional block
6 Services
7 User Network Interface and Service
Node Interface
8 Optical network requirements
8.1 Layered structure of optical
network
8.2 Physical medium dependent layer requirements for the wavelength
allocation
8.3 Physical medium dependent layer requirements for the ATM-PON
8.3.1 Digital signal nominal bit rate
8.3.2 Physical media and transmission
method
8.3.3 Bit rate
8.3.4 Line code
8.3.5 Operating wavelength
8.3.6 Transmitter at Old and Oru
8.3.7 Optical path between Old/Oru and Ord/Olu
8.3.8 Receiver at Ord and Olu
8.4 Physical medium dependent layer requirements for the
Enhancement Band
9 Operations Administration and
Maintenance (OAM) functionality
10 Performance
11 Environmental condition
12 Safety
Appendix I – Optical interface parameters examples for
ODN
I.1 Introduction
I.2 Examples
Appendix II – Deployment scenarios
II.1 Introduction
II.2 Configuration examples
II.2.1 Case 1: Reception of Basic Band only
II.2.2 Case 2: Reception of Basic Band and Enhancement Band signals by
separate ONUs
II.2.3 Case 3: Reception of Basic Band and Enhancement Band
signals by integrated ONUs
II.2.4 Case 4: Arrangement of WDMs to minimize upstream path loss
II.2.5 Case 5: ODNs with reduced attenuation range for Enhancement Band
II.2.6 Example in case of insufficiency
of loss budget between E-ONU
and E-OLT
Appendix III – Isolation between the Basic Band and the
Enhancement Band
III.1 Introduction
III.2 Example for required isolation at
Basic Band receiver from Enhancement Band signal
III.2.1 Video services
III.2.2 DWDM services
III.3 Example of isolation classes
III.4 Deployment examples
III.4.1 Model to be considered
III.4.2 In case of 64-QAM
III.4.3 Filter characteristics
Appendix IV – Effect of optical return loss of ODN
IV.1 Introduction
IV.2 Effect of ODN optical return loss
in the Basic Band
IV.2.1 Reflectance model to be considered
IV.2.2 Influence of reflectance into ONU receiver
IV.2.3 Influence of reflectance into OLT receiver (in the signal region)
IV.2.4 Influence of reflectance into OLT receiver (in the no signal region)
IV.2.5 Summary in effects of ODN optical return loss
in the Basic Band
IV.3 Influence of reflectance from
Enhancement Band to Basic Band
IV.3.1 Influence of reflectance into OLT receiver from Enhancement Band
Appendix V – Optical parameters for reference
point (c) and (e) and two example deployment cases
V.1 Introduction
V.2 Optical level diagram examples
V.2.1 Case 1: ODN centric view of optical
parameters
V.2.2 Case 2: Equipment centric view of optical
parameters
NOTE - This Recommendation uses the term
"ONU" to refer to both ONTs and ONUs. Any reference to ONUs includes
ONTs as well within this Recommendation.