1
Scope
2 References
3 Definitions
4 Abbreviations
5 General
5.1 Master-slave determination
5.2 Capability exchange
5.3 Logical channel signalling
procedures
5.4 Receive terminal close logical
channel request
5.5 H.223 multiplex table entry
modification
5.6 Audiovisual and data mode request
5.7 Round-trip delay determination
5.8 Maintenance loops
5.9 Commands and indications
Annex A – Messages: Syntax
Annex B – Messages:
Semantic definitions
B.1 Master-Slave Determination
messages
B.2 Terminal capability messages
B.3 Logical channel signalling
messages
B.4 Multiplex Table signalling
messages
B.5 Request Multiplex Table signalling
messages
B.6 Request Mode messages
B.7 Round-trip Delay messages
B.8 Maintenance Loop messages
B.9 Communication Mode Messages
B.10 Conference Request and Response
Messages
B.11 Multilink Messages
B.12 Logical Channel Bit rate Change
Messages
B.13 Commands
B.14 Indications
B.15 Generic messages
Annex C –
Procedures
C.1 Introduction
C.2 Master-slave determination
procedures
C.3 Capability exchange procedures
C.4 Unidirectional Logical Channel
signalling procedures
C.5 Bidirectional Logical Channel
signalling procedures
C.6 Close Logical Channel procedures
C.7 H.223 Multiplex Table Procedures
C.8 Request Multiplex Entry procedures
C.9 Mode Request procedures
C.10 Round-trip delay procedures
C.11 Maintenance Loop procedures
Annex D – Object
identifier assignments
Annex E – ISO/IEC
14496-2 Capability Definitions
Annex F – Logical
Channel Bit-Rate Management Capability Definitions
Annex G – ISO/IEC
14496-1 Capability Definitions
G.1 Capability Identifier
G.2 Capability parameters used for
capability negotiations and logical channel signalling
G.3 Capability parameters used for
logical channel signalling only
Annex H – ISO/IEC
14496-3 Capability Definitions
Annex I – GSM
Adaptive Multi-Rate Capability Definitions
I.1 Definition of mode signalling and bit
stuffing to achieve octet alignment
Annex J – TDMA ACELP
Voice Codec Definitions
Annex K – TDMA US1
Voice Codec Definitions
Annex L
– CDMA EVRC Voice Codec Definitions
Annex M – ISO/IEC
13818-7 and ITU-R BS.1196 Definitions
Appendix I – Overview
of ASN.1 syntax
I.1 Introduction to ASN.1
I.2 Basic ASN.1 data types
I.3 Aggregate data types
I.4 Object identifier type
Appendix II –
Examples of H.245 procedures
II.1 Introduction
II.2 Master-slave Determination Signalling
Entity
II.3 Capability Exchange Signalling
Entity
II.4 Logical Channel Signalling Entity
II.5 Close Logical Channel Signalling
Entity
II.6 Multiplex Table Signalling Entity
II.7 Mode Request Signalling Entity
II.8 Round-trip Delay Signalling Entity
II.9 Bidirectional Logical Channel
Signalling Entity
Appendix III –
Summary of procedure timers and counters
III.1 Timers
III.2 Counters
Appendix IV – H.245
extension procedure
Appendix V – The
replacementFor procedure
Appendix VI –
Examples of H.263 Capability Structure Settings
VI.1 Examples of Enhancement Layer
H.245 parameter setting
VI.2 Examples of Video Back Channel
H.245 parameter setting
Appendix VII –
Procedure and template for defining new capabilities with H.245 generic
capabilities
VII.1 Procedure
VII.2 Template
VII.3 Example Template – H.261
Appendix VIII – List
of generic capabilities and generic messages defined in
Recommendations/Standards other than this Recommendation
Appendix IX – ASN.1
usage in this Recommendation
IX.1 Tagging
IX.2 Types
IX.3 Constraints and Ranges
IX.4 Extensibility